Covers seamless carbon Grades A &B steel pipe for high pressure and high temperature service. Pipe is suitable for bending, flanging, and similar forming operations and for welding. Applications include: Refineries, Power Plants, Boilers, Ship Building, and other specialized applications.
Hot-finished pipe need not be heat treated. Cold-drawn pipe shall be heat treated after the final cold draw pass at a temperature of 1200°F or higher.
Hydrostatic & Nondestructive Electric Testing
Hydrostatic inspection test pressure is 2500 psi for sizes NPS 2 and under. Test pressure shall be maintained for a minimum of 5 seconds. When specified by the purchaser, pipe may be tested by the nondestructive electric test in lieu of the hydrostatic test.
End Finish Plain End:
NPS 1-1/2 and smaller shall be either plain end square cut or plain end beveled at the option of the manufacturer. NPS 2 ends shall be beveled to angle 30° +5°, -0° with a root face of 1/16” ± 1/32”.
Threaded Pipe:
Threads comply with ANSI Standard B 1.20.1
Couplings:
Couplings comply with ASTM Standard A 865
Available Coatings
ASTM A 106 seamless pipe is available in four different coatings:
- Exclusive Blue Diamond® Coating
- Hot-Dipped Galvanized
- Pickled and Oiled
- Bare
Chemical Requirements Composition, % Max
CarbonA Manganese Phosphorus Sulfur .25 0.27/0.93 .035 .035
Silicon CopperB NickelB ChromiumB
0.10 Min .40 .40 .15
MolybdenumB VanadiumB .15 .08
AFor each reduction of 0.01% below the specified carbon maximum, an increase of 0.06% manganese above the specified maximum will be permitted up to a maximum of 1.35%
BThe combination of these five elements shall not exceed 1.00%
Tensile Requirements
Yield Strength, min 35,000 psi
Tensile Strength, min 60,000 psi
Elongation in 2” 35% Minimum
Degree Diameter of Mandrel
Of Bend Standard 90° 12 X pipe O.D. Close Coiling 180° 8 X pipe O.D.
Frequency of Tests
Tensile tests and flattening tests are required on one length of pipe from each lot of 400 lengths or fraction thereof for each size.
The dimensions and weights furnished under this specification are in agreement with the standardized dimensions and weights specified in ANSI B 36.10.
Plain End Dimensions Schedules 40 & 80
|
|
Schedule 40 |
Schedule 80 |
Nominal Size |
O.D. Inches |
Wall |
Weight, Lb/Ft |
Wall |
Weight, Lb/Ft |
1/8 |
0.405 |
.068 |
0.24 |
.095 |
0.31 |
1/4 |
0.540 |
.088 |
0.43 |
.119 |
0.54 |
3/8 |
0.675 |
.091 |
0.57 |
.126 |
0.74 |
1/2 |
0.840 |
.109 |
0.85 |
.147 |
1.09 |
3/4 |
1.050 |
.113 |
1.13 |
.154 |
1.48 |
1 |
1.315 |
.133 |
1.68 |
.179 |
2.17 |
1-1/4 |
1.660 |
.140 |
2.27 |
.191 |
3.00 |
1-1/2 |
1.900 |
.145 |
2.72 |
.200 |
3.63 |
2 |
2.375 |
.154 |
3.66 |
.218 |
5.03 |
Plain End Dimensions Schedules 160 & XXS
|
|
Schedule 160 |
Schedule XXS |
Nominal Size |
O.D. Inches |
Wall |
Weight, Lb/Ft |
Wall |
Weight, Lb/Ft |
1/8 |
0.405 |
N/A |
N/A |
N/A |
N/A |
1/4 |
0.540 |
N/A |
N/A |
N/A |
N/A |
3/8 |
0.675 |
N/A |
N/A |
N/A |
N/A |
1/2 |
0.840 |
.188 |
1.31 |
.294 |
1.72 |
3/4 |
1.050 |
.219 |
1.95 |
.308 |
2.44 |
1 |
1.315 |
.250 |
2.85 |
.358 |
3.66 |
1-1/4 |
1.660 |
.250 |
3.77 |
.382 |
5.22 |
1-1/2 |
1.900 |
.281 |
4.86 |
.400 |
6.41 |
2 |
2.375 |
N/A |
N/A |
N/A |
N/A |
Permissible Variations in Wall Thickness
Minimum wall thickness at any point shall not be more than 12.5% under nominal wall thickness specified. Maximum wall thickness at any point shall not be greater than 20.0% over nominal wall thickness.
Workmanship
Visual imperfections such as scabs, seams, laps or tears shall not exceed 5% of the nominal wall thickness.
Permissible Variations in Outside Diameter
NPS 1-1/2 and under ± 1/64” NPS 2 ± 1/32”
Permissible Variations in Weight per Foot
Pipe shall not vary more than 10% over and 3.5% under the standard specified.
Product Marking
Each length of pipe is continuously stenciled to show the manufacturer, specification (A106), size (O.D. & wall), “A & B” for Grades A & B, 2500 psi, length and heat number
Manufacturing Location
All product furnished by Wheatland Tube Company and Sharon Tube Company are manufactured by Sharon Tube in Sharon, PA, USA.
Hot-Dipped Galvanized
Pipe is galvanized to the requirements of ASTM A 53. The average weight of zinc coating shall not be less than 1.8 ounces per square foot of surface (inside and outside).
When galvanized pipe is bent or otherwise fabricated to a degree that causes the zinc coating to stretch or compress beyond the limit of elasticity, some flaking of the coating may occur.
| ASTM A106 |
| Seamless carbon steel pipes for high-temperature service |
| Application:
| For high temperature service |
| Size(mm):
| O.D.: 6.0～323.0 W.T.: 1～30 L: max 12000 |
| Grade |
C≤ |
Mn |
P≤ |
S≤ |
Si≥ |
Cr≤ |
Cu≤ |
Mo≤ |
Ni≤ |
V≤ |
| A |
0.25 |
0.27-0.93 |
0.035 |
0.035 |
0.10 |
0.40 |
0.40 |
0.15 |
0.40 |
0.08 |
| B |
0.30 |
0.29-1.06 |
0.035 |
0.035 |
0.10 |
0.40 |
0.40 |
0.15 |
0.40 |
0.08 |
| C |
0.35 |
0.29-1.06 |
0.035 |
0.035 |
0.10 |
0.40 |
0.40 |
0.15 |
0.40 |
0.08 |
Grade |
Rm
Mpa Tensile Strength |
Mpa
Yield Point |
A％
Elongation |
Delivery Condition |
| A |
≥330 |
≥205 |
20 |
Annealed |
| B |
≥415 |
≥240 |
20 |
Annealed |
| C |
≥485 |
≥275 |
20 |
Annealed |
| Pipe Type |
Pipe Sizes |
Tolerances |
| Cold Drawn |
OD |
≤48.3mm |
±0.40mm |
| ≥60.3mm |
±1％mm |
| WT |
±12.5％ |
>> Conversion Calculator Calculation-Pressure|Weight|Temperature|Volume|Length
>> Pipe Plate Bar Square Pipes Weight Calculation Tool
>> Metals Weight Calculator-Aluminum|Brass|Bronze|Copper|Magnesium|Plastic|Nickel|Stainless Steel|Steel|Titanium
>> Pressure Ratings for standard seamless stainless steel pipes
>> Pressure and Temperature Ratings of ASTM A106 Grade B Carbon Steel Pipes
>> Internal Pressure Calculation
>> Flow Capacity, ANSI Schedule 40 Pipe
>> Steel Pipe (Low Carbon) Burst Pressures
>> Brinell and Rockwell Hardness Conversion Chart
>> Maximum Working Pressure-ASTM A53 B Carbon Steel Pipes
>> Pressure and Temperature Ratings of ASTM A106 Grade B Carbon Steel Pipes
>> Stainless Steel Tube Dimension
>> Stainless Steel Tube Guage
>> ANSI Standard Pipe Chart
>> Millimeters Inches Conversion Chart
>> Conversion Table of Temperatue, Length,Mass,Pressure
>> NPS-Nominal-Pipe-Size
>> NPS-Nominal-Pipe-Size and DN - Diametre Nominal
>> Pipe Schedule
|