| Products |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
EN 10088-1 gives a limited amount of data for specification purposes. Above ambient temperature this is limited to modulus of elasticity (Youngs modulus) and coefficients of thermal expansion. The maximum temperature for which there is data is 500 degC. There is more detailed 'typical' data in the INCO publication 'Austenitic chromium-nickel stainless steel-engineering properties at elevated temperature.This including tensile and shear modulus data, Poisson's ratio, density, thermal expansion, conductivity, specific heat and electrical resistivity. A selection from this data is tabulated in this article for the common austenitic grades only. Some of the data shown in this article is interpolated from graphs in the original publication. Elevated temperature modulii of elasticity and coefficients of expansion for stainless steel specified in EN 10088-1The table below is based on the reference data presented in EN 10088-1. Only a sample of the information is shown for the most commonly used stainless steel tube types. These are grouped using 'AISI' steel types. The separate table indicates some of the grades that have been grouped together.
Some of the EN grades covered by the 'steel types' are shown in the following table.
Elevated temperature physical properties for austenitic stainless steels (INCO Publication 2980 Data)The tables are based on graphs and tables shown in the INCO publication 'Austenitic chromium-nickel stainless steels-engineering properties at elevated temperatures'. This data is based on measured values, usually reported in 'fps' units with temperatures in degrees Fahrenheit. Here, these have been taken as the nearest values and so are for guidance only, not for specification purposes. Only part of the available data is shown here. The full publication (INCO 2980) is available from the Nickel Development Institute Modulus of Elasticity (E) and Rigidity(Shear) (G) (E/G)
Units are kgf/mm2 x 103 (multiply by 9.807 to convert to N/mm2) Poisson's Ratio
Poisson's ratio does not have any units. Density
Units have been converted in this table into Kg/m3 Thermal Expansion These are 'average' values between 20 degC and the temperature shown, not 'instantaneous' values ie specific values for the temperature shown. The values are taken from the graph, Fig31, and so are subject to some interpretation from the curves plotted.
The units are 10-6 x C-1 Thermal Conductivity
The units used on Fig 29 of the INCO publication are kcal/m.hr.degC Specific Heat
The units are J/kg.K Electrical Resistivity
Polishing Polished Seamless Stainless Steel Pipe Tube Stainless Steel Tubes Surface Roughness Review Stainless Steel Bright Annealing/Annealed Tubes China USA Surface Roughness Standard Comparison Surface Roughness Conversion Chart of Stainless Steel Tube British and American standards for tolerances, surface finish and testing of stainless steels Cleaning of Stainless Steel Tubes Corrosion Resistant Stainless Steel Tube Coroosion Resistane of Stainless Steel Tubes High Temperature Stainless Steel Tubes Heat resistant Stainless Steel Tubes High Temperature-Tubes and Pipes Standard Related References: Physical Properties Table of Metals Physical Properties of Stainless Steel Physical Properties of Stainless Steel and Carbon Steel Physical Properties of Gases at Standard Temperature Pressure Physical Properties of HDG Hot-Dip Galvanized Physical Properties of Zirconium EN 10088-1 Elevated Temperature Physical Properties of Steel
Properties | Tensile Strength | Yield Strength | Typical Yield | Typical Tensile | Yield strength & Yield point | Stainless Steel Tensile Strength | Bend Testing | Compression Testing | Difference Between Yield and Tensile | AISI Steel Yield Tensile | Strength Properties of Metals | Strength of Materials | Stress | Aluminum Mechanical Properties | Tensile Proof Stress Of Metric Bolts and Screws | Tensile Strength of Metric Nuts | Stainless Tensile Of Metric Bolts Screws Physical Properties Stainless Steel Carbon Steel | Thermoplastics Physical Properties | British Standard Strength of Steel | Shear and Tensile | Elastic Properties Young Modulus | Stength European Standard | Ductility | Young's Modulus | Non-Ferrous Modulus of Elasticity | Steel Bolts Strength | Iron Steel Modulus of Elasticity | Thermal Properties | Properties of Thermal | Thread Shear Calculator | Metals Properties | Stainless Steel Physical Properties | Definition Mechanical Properties |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
